Generator Crankshaft Thrust Washer: Function, Wear and Replacement
The crankshaft thrust washer is the bearing component that controls the axial position of the crankshaft and absorbs the axial thrust loads in a diesel engine. In a generator set, the axial thrust comes from the clutch engagement, the torque converter, the hydraulic drive, and the internal forces of the engine itself, and the thrust washer prevents the crankshaft from moving beyond its designed end float and damaging the main bearings, the oil seals, the connecting rods, and the flywheel. This guide covers the function of the thrust washer, the thrust bearing designs, the end float and the measurement, the wear and the failure modes, the symptoms, the replacement procedure, and the selection for the common engine families.
The thrust washer is usually located at the rear main bearing of the engine, where the thrust loads are concentrated, and it is manufactured from the same bearing materials as the main bearings, with the babbit or the aluminium-tin overlay on the steel or the bronze backing. The thrust washer carries the axial load on its face, and the crankshaft thrust face runs against the washer surface with a controlled oil film. The clearance between the thrust faces is the crankshaft end float, and it is a critical setting in the engine assembly.
What Does the Crankshaft Thrust Washer Do?
The crankshaft thrust washer, also called the thrust bearing or the thrust half, is the component that locates the crankshaft axially in the engine block. The crankshaft is subjected to the axial forces during the operation: the clutch and the PTO loads push the crankshaft towards the flywheel end, the torque converter and the hydraulic loads push it in the opposite direction, and the helical gears and the internal forces add their components. The thrust washer provides the bearing surface that absorbs these loads and keeps the crankshaft in its correct axial position.
The thrust washer is fitted in the bearing housing, usually at the rear main bearing, and it is made in two halves that form the complete ring around the crankshaft journal. The thrust faces are grooved to distribute the oil, and the oil is supplied from the main bearing oil feed. The crankshaft is machined with the thrust faces at the rear journal, and the washer runs against these faces.
The end float, the axial clearance between the crankshaft and the thrust washers, is set by the design to allow for the thermal expansion and the oil film, typically 0.10 to 0.40 mm on the diesel engines. The end float is measured with the dial gauge during the assembly, and it is corrected by the selection of the thrust washer thickness. The crankshaft guide covers the shaft component, and the main bearing guide covers the radial bearings.
Thrust Bearing Designs
The thrust washer designs follow the bearing system of the engine:
| Design | Construction | Typical Application | Notes |
|---|---|---|---|
| Flanged main bearing | Main bearing with integral thrust flanges | Small and medium engines | Simple, combined radial and thrust bearing |
| Separate thrust washer | Half-ring washers in the bearing housing | Medium and large engines | Independent sizing and replacement |
| Multi-groove thrust bearing | Grooved faces with high load capacity | Heavy-duty and high-thrust engines | Improved oil film and load distribution |
The flanged main bearing has the thrust flanges formed on the sides of the bearing shell, and it is the simplest design used on the small engines. The separate thrust washer is a half-ring fitted in a groove in the block or the bearing cap, and it is used where the thrust load is higher and the washer is replaced independently of the main bearing.
The multi-groove thrust bearing has the oil grooves machined on the face, which improves the oil film formation and the load capacity, and it is used on the engines with the high axial loads. The thrust washer material is matched to the crankshaft: the aluminium-tin, the copper-lead, or the tri-metal materials are used, and the overlay protects the crankshaft face.
The thrust washer is identified by the part number and the thickness grade, and the replacement is made with the correct grade to restore the end float. The main bearing guide covers the bearing materials, and the flywheel guide covers the axial load source.
End Float and Measurement
The crankshaft end float is the axial clearance between the crankshaft thrust faces and the thrust washers, and it is measured with the dial gauge:
- Mount the dial gauge on the engine block, with the plunger against the crankshaft flange or the flywheel face.
- Move the crankshaft axially in one direction with a lever or a pry bar, and zero the gauge.
- Move the crankshaft in the opposite direction, and read the total movement.
- Compare the reading with the engine specification, and record the value.
The end float specification for the diesel engines is typically 0.10 to 0.40 mm, and the exact value is set by the engine manufacturer. If the end float is too small, the crankshaft binds against the washers when the engine warms up; if the end float is too large, the crankshaft knocks and the thrust faces hammer, accelerating the wear. The end float is adjusted by the selection of the thrust washer thickness: the washers are available in the standard and the oversize grades.
The end float is checked at the assembly, at the bearing inspection, and when the axial knock is suspected. The measurement is made with the engine cold and the crankshaft free of the load. The maintenance schedule guide covers the bearing checks, and the troubleshooting guide covers the knock diagnosis.
Wear and Failure Modes
The thrust washer wears in service, and the wear is accelerated by the high thrust loads, the clutch misuse, the oil starvation, the contamination, and the misalignment. The common failure modes are:
- Face wear: the thrust face wears and the end float increases, causing the knock and the hammering.
- Scoring and pick-up: the contamination or the oil starvation scores the face, and the material transfers to the crankshaft.
- Spalling and fatigue: the repeated high loads fatigue the overlay, and the material flakes off.
- Overheating: the oil starvation or the excessive load overheats the washer, and the overlay melts or discolours.
- Misalignment wear: the worn main bearings allow the crankshaft to run off, and the thrust face wears unevenly.
The wear of the thrust washer is detected by the increased end float, the axial knock, the oil pressure drop, and the metal particles in the oil analysis. The worn washer is replaced, and the cause of the wear is investigated: the clutch adjustment, the oil supply, the bearing condition, and the alignment are checked. The troubleshooting guide covers the diagnosis, and the clutch plate guide covers the thrust load source.
Symptoms of Thrust Washer Failure
The symptoms of a worn or failed thrust washer are distinctive:
- An axial knock or a thump from the rear of the engine, especially when the clutch is engaged or the load is applied.
- The crankshaft moves visibly when the flywheel is rocked axially.
- The oil pressure fluctuates or drops, as the worn bearing opens the clearances.
- The metal particles appear in the oil analysis, with the babbit or the overlay material.
- The engine stalls or the clutch drags when the crankshaft moves out of position.
- The oil seal leaks, as the crankshaft moves axially and wears the seal lip.
The diagnosis is confirmed by the end float measurement and the inspection of the thrust faces. The repair is an in-frame or an out-of-frame operation depending on the engine design: the rear main bearing cap is removed, the thrust washer is replaced, and the end float is set. The troubleshooting guide covers the symptoms, and the oil seal kit guide covers the related seal.
Replacement Procedure
The replacement of the thrust washer follows the bearing service procedure:
- Drain the oil and remove the oil pan, and access the rear main bearing cap.
- Remove the bearing cap, and remove the lower thrust washer half from the cap.
- Rotate the crankshaft to release the upper thrust washer half, and remove it with care.
- Inspect the crankshaft thrust face for the scoring and the damage, and the main bearing for the wear.
- Install the new upper and lower thrust washer halves with the oil grooves facing the crankshaft.
- Install the bearing cap with the correct torque and sequence, and check the end float.
- Refit the oil pan, fill the oil, and test the engine at the idle and the load.
The procedure is performed with the correct tools and the clean conditions. The thrust washers are installed with the locating tabs in the grooves, and the oil grooves are aligned with the oil feed. The end float is measured before the oil pan is refitted, and the adjustment is made with the washer grade if required.
The replacement is often combined with the main bearing service, and the complete bearing set is installed where the engine is rebuilt. The crankshaft thrust face is dressed or the crankshaft is replaced if the face is badly scored. The installation guide covers the procedure, and the main bearing guide covers the related service.
Selecting the Correct Thrust Washer
The thrust washer is selected from the engine model, the bearing size, the thrust washer grade, and the original part number. The washer is identified by the journal diameter, the width, the thickness grade, and the material, and the replacement is made with the identical or the verified equivalent part.
The oversize grades are used where the crankshaft thrust faces have been ground: the washer thickness is increased by the oversize amount, and the end float is restored. The material is matched to the crankshaft material and the load: the tri-metal washers are used for the high-load engines, and the standard aluminium-tin washers for the normal service.
The order information includes the engine model, the bearing position (rear main), the journal diameter, and the part number. The common grades are stocked in the bulk, and the kits are prepared for the engine overhaul. The sourcing guide explains the order data, and the engine overhaul kit guide covers the complete bearing sets.
Thrust Load Sources in Generator Drives
The axial thrust loads in a generator drive come from several sources, and the thrust washer is designed to carry the combined load. The clutch engagement applies the axial load through the release mechanism and the friction surfaces, and the repeated engagement and the misuse add the shock loads. The hydraulic pumps, the torque converters, and the PTO drives apply the axial loads through the shafts and the couplings, and the misaligned couplings add the cyclic axial forces. The helical gear drives and the timing gears apply the axial components of the tooth forces, and the engine internal forces from the crank and the connecting rod geometry add the periodic thrust.
The magnitude and the direction of the thrust are different in each drive configuration: the generator coupled through the flexible coupling applies a small axial load, while the clutch and the hydraulic drives apply the significant loads in the axial direction. The thrust washer is designed for the worst-case combination of the steady and the transient loads, and the oil film is maintained under the full load. The drive configuration is reviewed during the troubleshooting: the repeated thrust washer failures indicate the excessive or the misaligned axial load, and the drive is inspected for the alignment and the clutch adjustment. The clutch pressure plate guide covers the clutch load, and the flywheel guide covers the coupling.
Thrust Washer Material Selection
The thrust washer materials are selected for the load, the speed, and the operating conditions. The aluminium-tin bearing material is the standard for the moderate loads: it has the good anti-seizure properties and the conformability, and it protects the crankshaft. The copper-lead and the tri-metal materials carry the higher loads and have the higher fatigue strength, and they are used on the heavy-duty engines. The bimetallic and the trimetal constructions combine the steel backing with the bearing layer, and the overlay is applied for the running-in and the corrosion resistance.
The selection is matched to the engine manufacturer specification and the crankshaft material: the washer and the shaft form a tribological pair, and the wrong material causes the seizure, the wear, or the shaft damage. The oil and the filtration are part of the selection: the clean oil at the correct pressure maintains the film, and the contamination accelerates the wear of any material. The replacement washer is the same material and the grade as the original, and the verified equivalent is confirmed against the part number. The main bearing guide covers the bearing materials, and the oil filter guide covers the oil cleanliness.
Engine Assembly and Bearing Inspection
The engine assembly sets the thrust washer condition for the life of the engine: the bearing bores are clean and the correct size, the crankshaft is inspected and the journals are measured, and the thrust faces are checked for the squareness and the finish. The main bearing caps are torqued in the correct sequence and to the correct value, and the crankshaft is rotated to check the freedom. The end float is measured and set at the assembly, and the thrust washer grade is selected to give the specified clearance.
The bearing inspection during the overhaul follows the procedure: the main bearings are measured with the plastigage or the micrometer, the crankshaft journals are measured for the ovality and the taper, and the thrust washer is measured for the thickness and the face condition. The bearing shells are inspected for the contact patterns, the corrosion, and the fatigue, and the oilways are checked for the cleanliness. The inspection results are compared with the limits, and the components are replaced within the limits. The assembly record documents the measurements and the settings. The engine overhaul kit guide covers the complete service, and the oil pump guide covers the oil supply.
Thrust Washer Fit and Lubrication
The wear is detected early by the oil analysis and the end float measurement: the increasing iron and the aluminium particles in the oil analysis indicate the bearing and the washer wear, and the end float beyond the limit indicates the thrust washer loss. The inspection interval is shortened when the wear trend is detected, and the corrective action is planned before the crankshaft is damaged. The early detection and the replacement are far more economical than the crankshaft grinding or the replacement, and the record of the measurements supports the condition-based maintenance of the engine.
The fit of the thrust washer in the bearing housing is controlled: the washer half sits in the groove or the register, the locating tab engages the slot, and the washer is free to move slightly for the alignment. The washer is not forced or filed to fit, and the bore is cleaned before the installation. The crankshaft thrust face is smooth and the correct width, and the washer face is the full contact. The clearance between the washer and the crankshaft flange is the end float, and the correct grade is selected to give the specified value.
The lubrication of the thrust washer is by the oil from the main bearing feed: the oil passes through the groove to the thrust face, and the wedge film forms under the rotation. The oil supply is maintained by the oil pressure and the flow, and the oil is clean and at the correct temperature. The thrust face is grooved to distribute the oil, and the groove orientation is correct at the installation. The oil starvation causes the face wear and the seizure, and the oil pressure and the filter are part of the thrust washer reliability. The oil pump guide covers the supply, and the oil filter guide covers the filtration.
The lubrication condition is verified at the service: the oil pressure is recorded, the oil analysis is reviewed for the metal particles, and the bearing surfaces are inspected. The thrust washer is measured for the thickness and the face condition, and the end float is recorded. The correct fit and the lubrication give the long thrust washer life, and the failures are traced to the fit, the lubrication, or the load. The assembly record and the oil records are kept together, and the maintenance is planned from the trends. The maintenance schedule guide covers the checks, and the main bearing guide covers the related bearing.
Frequently Asked Questions
Need a crankshaft thrust washer for your generator engine?
Contact us with the engine model and the bearing details for the correct washer grade, with verified quality and fast shipping.
